will turn over, started before changing fuelpump or tranny but not after
96 mustang changed tranny and fuel pump. has gas won't start need help?
check the oil, engine oil that is. or the radiator.
96 mustang changed tranny and fuel pump. has gas won't start need help?
the question u need to ask is what plug under the hood is not plugged in at all or not connected all the way. im asuming the trans was not done in a shop and the motor was let to hang once the trans was removed and it prob pulled a plug partally apart.
i am a hot rod builder and love to see a new fuel injected monster in a old car. latest project is a 96 4.6 ltr. in to a 32 rat rod all comp controlled and daily driveable.
Tough question because if it used to run, it should run after tranny and fuel pump, since it cranks and has fuel pressure.
My best guess is that in order to take out the tranny, you had to take out the starter at well, and when you put the wires back on, you left off the power to the igntion or fuel injection.
Use an inductive timing light or spare spark plug to determine if you have spark.
If you don't, then it is a question of power to the ignition circuit.
Second though is just having fuel at the rail is not the same as having enough pressure.
has gas up to the rail you say? it could be the fuel pump regulator stopping the gas from reaching the injectors. in case you don,t know where it is, it,s bolted up on the fuel rail. it can,t be the pump or the fuel filter if gas is reaching up to the rail. and it can,t be the relay or the pump would,nt kick on. change the regulator and see if it starts.
Tuesday, October 25, 2011
Have 1989 chevy truck v8 tbi going to install 1976 chevy v8 with carb.changed fuel pump now what?
do i change distributor to wire it up? alternators? is that all? HELP....
Have 1989 chevy truck v8 tbi going to install 1976 chevy v8 with carb.changed fuel pump now what?
Yeah you want the old style distributer with the vacum advance since the one that came with the tbi engine is controlled by the ecm.
Have 1989 chevy truck v8 tbi going to install 1976 chevy v8 with carb.changed fuel pump now what?
why are you leaving the throttle body and going to the carb? buy a chilton's if you are mechanically inclined. It is a very useful manual and should answer most questions you will have later also.
You're going to need all the wiring from the 89 along with the sensors and PCM changed into the 76. You might even need the steering column of at least some more power supplies to the motor. This is a big job.
Have 1989 chevy truck v8 tbi going to install 1976 chevy v8 with carb.changed fuel pump now what?
Yeah you want the old style distributer with the vacum advance since the one that came with the tbi engine is controlled by the ecm.
Have 1989 chevy truck v8 tbi going to install 1976 chevy v8 with carb.changed fuel pump now what?
why are you leaving the throttle body and going to the carb? buy a chilton's if you are mechanically inclined. It is a very useful manual and should answer most questions you will have later also.
You're going to need all the wiring from the 89 along with the sensors and PCM changed into the 76. You might even need the steering column of at least some more power supplies to the motor. This is a big job.
2002 cavalier won't start. 2 months ago changed the fuel pump thinking it was that.?
some more information would be helpful, however my first guess is an in line fuel filter. And if you have been buying gas at those inexpensive gas stations, crawl under the car, find the fuel filter change it to a new one then go fill your car up with chevron unleaded and drive drive drive until the tank is low, then fill it up again, here is why
el cheapo gas companies buy what is called bid gas, this is gas that is contaminated with water and tiny bits of crap. (too many particles per billion) the good companies like chevron and costco and some others, refuse to buy this from the refineries. and have placed orders with the refineries, ahead of time and ordered good gas with their own additives. And some other company bids on the contaminated fuel, it is gas, your car will run on it, but over time, hard deposits can build up, which plug up fuel filters and fuel injectors over time.
I like chevron, it has techron, which is a fuel system cleaner you can buy in any auto parts store. However, it is easier to pay a few more cents a gallon now, and keep your fuel system clean to begin with, than go back and try to clean out tine orifices that are in fuel injection systems later.
if you have a fuel pump in the gas tank, it was designed to run cooler, by being surrounded by fuel, so it is best to keep your tank full, and as an added benefit, a full tank, means less condensation (water) on the metal surfaces inside the tank, (particularly in winter) if you keep your tank mostly empty, and use inexpensive fuels, this can cause long term problems, such as excess water in the gas, and plugged fuel filters things like that which can mimic fuel pump problems.
2002 cavalier won't start. 2 months ago changed the fuel pump thinking it was that.?
Need more info. Does the engine turn over and not start? 1st ck to see if its delivering fuel to determine if its a fuel problem. If it isnt you can ck the in line fuel filter and all fuses. Find out if cavaliers have a fuel pump reset switch. If all thats ok follow the wire harness from the pump to where it ends and ck for damaged wires. When you turn the key to accesessary or 1st click w/out trying to start you should hear the fuel pump cycle for about 15 seconds. Hope this helps.
2002 cavalier won't start. 2 months ago changed the fuel pump thinking it was that.?
1) check battery
2) check fuses
3) check your gas cap is on completely
4) alternator problem
5) starter problem
6) fuel pump problem.
although if your car has driven since the fuel pump swap, chance are its not that. My first guess is the battery, and other elements of the electrical.
What sound does the car make when turning over?
Does it make any noise when you try to start it?database ittwit
el cheapo gas companies buy what is called bid gas, this is gas that is contaminated with water and tiny bits of crap. (too many particles per billion) the good companies like chevron and costco and some others, refuse to buy this from the refineries. and have placed orders with the refineries, ahead of time and ordered good gas with their own additives. And some other company bids on the contaminated fuel, it is gas, your car will run on it, but over time, hard deposits can build up, which plug up fuel filters and fuel injectors over time.
I like chevron, it has techron, which is a fuel system cleaner you can buy in any auto parts store. However, it is easier to pay a few more cents a gallon now, and keep your fuel system clean to begin with, than go back and try to clean out tine orifices that are in fuel injection systems later.
if you have a fuel pump in the gas tank, it was designed to run cooler, by being surrounded by fuel, so it is best to keep your tank full, and as an added benefit, a full tank, means less condensation (water) on the metal surfaces inside the tank, (particularly in winter) if you keep your tank mostly empty, and use inexpensive fuels, this can cause long term problems, such as excess water in the gas, and plugged fuel filters things like that which can mimic fuel pump problems.
2002 cavalier won't start. 2 months ago changed the fuel pump thinking it was that.?
Need more info. Does the engine turn over and not start? 1st ck to see if its delivering fuel to determine if its a fuel problem. If it isnt you can ck the in line fuel filter and all fuses. Find out if cavaliers have a fuel pump reset switch. If all thats ok follow the wire harness from the pump to where it ends and ck for damaged wires. When you turn the key to accesessary or 1st click w/out trying to start you should hear the fuel pump cycle for about 15 seconds. Hope this helps.
2002 cavalier won't start. 2 months ago changed the fuel pump thinking it was that.?
1) check battery
2) check fuses
3) check your gas cap is on completely
4) alternator problem
5) starter problem
6) fuel pump problem.
although if your car has driven since the fuel pump swap, chance are its not that. My first guess is the battery, and other elements of the electrical.
What sound does the car make when turning over?
Does it make any noise when you try to start it?
1999 nissan maxima won't start. changed fuel pump and have spark?
OK, tech stuff is nice if you know what your doing or maybe you play around with your car alot. But lets start, with the idea that you don't know anything and would like to take a shot at finding the problem. First off when you say %26quot;won't start', does this means that the engine cranks but won't fire up. So lets start from the beginning. Your battery should have 14.5 volts at a standstill. Use a volt meter to ck this. Then crank the engine with your key. The cranking voltage can't go below 10.5 volts or the engine won't start. At this point lets say that the engine cranks and has the required voltage. This solves the possible first problem area. Next pull a spark plug and look at its color. If its black and wet, the plug is fouled out and will need to be cleaned or replaced. Next if you have a good spark plug or a screwdriver, ck that you have spark. Ok , lets say the plugs are good and you have spark, so we go on to fuel. When we had carbs it was simple, but with fuel injection the rules changed. First crank the engine and using a screw driver (one that is long) put one end on the injector base and the hander end to your ear. You should hear a tapping or clicking noise. You hear the noise, that's good, no noise, get the car to a dealer. Next you need a fuel pressure gague. Your fuel system is a closed loop type. Meaning, at the the you crank the engine, there should be fuel comming from the gas tank to the engine and back. Not only do you need fuel flow but you also need pressure. I don't remember the correct pressure, but a steady 35 lbs. will do. Now stop cranking the engine, your pressure should stay. If it drops real fast you have a problem or two. Example: open injector, open one way value, leaking fuel line and such. At this point something should show up as being wrong, including the anti-thief system. If your problem does not show itself, get your car to the dealer. You could even have a mechanical problem or maybe two problems. Just remember to do the easy things first, maybe your out of fuel. Now if you can follow what I have said, them good. If I lost you, just get the car to a dealer. This is as simple as I can make it for you. Good luck, T-Bear.
1999 nissan maxima won't start. changed fuel pump and have spark?
How about this one. You recently lost a key and had one made. or the spair key is now being used? Sound likely? or the key your using is beat up. 1999 Maxima's have Imobilizer called NATS embedded Chip key. That chip close to the antennia coil around the ingnition lock sends a signal to the Smart Entry control that allows the ECM to turn on and car to start. If you used a NOID light you would see that the injector pulse was not there. Nissan calls this LOCK MODE, motor cranks but does not start. TOW the car to a dealership gather up all the keys and have nissan reprogram all of them they can and cut a couple of extra keys. Really Good Lock Smiths! with computerized Key systems can do it also.
1999 nissan maxima won't start. changed fuel pump and have spark?
Well you first need to find out if there is fuel pump pressure. Just changing the pump doesent mean there is pressure. Next you need to find if there is an injector pulse( meaning the injuctors are fireing. You need what is called a noud( from the auto store). THis device will flash when it id conected to the injuctor plug. If there is no pausle then you have a crank and or a cam senser out and it will have spark but will not turn on the injuctors.
Not sure on the question however hope this will help all those before shelling out thousands of dollars to those crooks called mechanics.. This is the problem I ran into. Cold starts dies out unless you rev up your engine. 1. Clean Mass Air Sensor with spray %26quot;MAF%26quot;.. 2. Get a Intake Cleaner/Carb Cleaner and spary the intake. Gas once dried can become thick and stickie. 3. Clear your codes from any Autozone for free. This should be your solution to your O2's, Knock Sensor, Misfire, Idle Control etc etc readings. It worked for me and hopefully will work for you. It's quite simple Keep your intake clean and replace filter regularly. Air and Gas creates the engines power and if not mixed properly with restrictions the computer will go crazy and will not be sure what the actual problem is.. I think its Nissan's scam.. = ) God Bless
1999 nissan maxima won't start. changed fuel pump and have spark?
How about this one. You recently lost a key and had one made. or the spair key is now being used? Sound likely? or the key your using is beat up. 1999 Maxima's have Imobilizer called NATS embedded Chip key. That chip close to the antennia coil around the ingnition lock sends a signal to the Smart Entry control that allows the ECM to turn on and car to start. If you used a NOID light you would see that the injector pulse was not there. Nissan calls this LOCK MODE, motor cranks but does not start. TOW the car to a dealership gather up all the keys and have nissan reprogram all of them they can and cut a couple of extra keys. Really Good Lock Smiths! with computerized Key systems can do it also.
1999 nissan maxima won't start. changed fuel pump and have spark?
Well you first need to find out if there is fuel pump pressure. Just changing the pump doesent mean there is pressure. Next you need to find if there is an injector pulse( meaning the injuctors are fireing. You need what is called a noud( from the auto store). THis device will flash when it id conected to the injuctor plug. If there is no pausle then you have a crank and or a cam senser out and it will have spark but will not turn on the injuctors.
Not sure on the question however hope this will help all those before shelling out thousands of dollars to those crooks called mechanics.. This is the problem I ran into. Cold starts dies out unless you rev up your engine. 1. Clean Mass Air Sensor with spray %26quot;MAF%26quot;.. 2. Get a Intake Cleaner/Carb Cleaner and spary the intake. Gas once dried can become thick and stickie. 3. Clear your codes from any Autozone for free. This should be your solution to your O2's, Knock Sensor, Misfire, Idle Control etc etc readings. It worked for me and hopefully will work for you. It's quite simple Keep your intake clean and replace filter regularly. Air and Gas creates the engines power and if not mixed properly with restrictions the computer will go crazy and will not be sure what the actual problem is.. I think its Nissan's scam.. = ) God Bless
How do you change the fuel pump in a 2001 Chevy Cavalier?
You have to drop the gas tank. The pump is probably in the tank (not sure of 2001 pump placement). Before you drop the tank, jack up the back of the car, support it well with jack stands, and look just in front of the tank. It could be located there.
How do you change the fuel pump in a 2001 Chevy Cavalier?
One of our associates who works on cars suggest that you access the AutoZone Web site for information on the process to replace the fuel pump.
There are many guides to replacing various vehicle components posted on the site as well. Here's the URL.:
http://www.autozone.com/shopping/repairG鈥?/a>
For more articles, previews, reviews of new- and used-vehicles, as well as photos, videos, blogs and quality ratins, please visit JDPower.com.
How do you change the fuel pump in a 2001 Chevy Cavalier?
You have to raise the car up very high. You have to drain the gas tank, then lower the gas tank down by undoing all the tank straps. Then un bolt the old fuel pump off the top of the tank and then put the new one on. Then repeat the process. Its strenious if you dont have enough height when you lift the car..
How do you change the fuel pump in a 2001 Chevy Cavalier?
One of our associates who works on cars suggest that you access the AutoZone Web site for information on the process to replace the fuel pump.
There are many guides to replacing various vehicle components posted on the site as well. Here's the URL.:
http://www.autozone.com/shopping/repairG鈥?/a>
For more articles, previews, reviews of new- and used-vehicles, as well as photos, videos, blogs and quality ratins, please visit JDPower.com.
How do you change the fuel pump in a 2001 Chevy Cavalier?
You have to raise the car up very high. You have to drain the gas tank, then lower the gas tank down by undoing all the tank straps. Then un bolt the old fuel pump off the top of the tank and then put the new one on. Then repeat the process. Its strenious if you dont have enough height when you lift the car..
I changed my fuel pump regulator and my truck will not start, what do i need to check?
You need to have the fuel pump pressure checked.
If there is no pressure check these things before you change the pump
The fuse
The rely
I changed my fuel pump regulator and my truck will not start, what do i need to check?
Alternator, if it has one, starter, plugs and wires, fan belts.
I changed my fuel pump regulator and my truck will not start, what do i need to check?
air in the fuel rail. look for what looks like a tire valve on the fuel rail.take the cap off depress the needle valve inside while someone cranks the truck,do this until gas starts to come out.truck should start.Did you change you fuel filter?Are you sure the regulator was the problem? Might have a bad fuel pump.
maybe fuel pump was the problem? check for fuel pressure and spark.
If there is no pressure check these things before you change the pump
The fuse
The rely
I changed my fuel pump regulator and my truck will not start, what do i need to check?
Alternator, if it has one, starter, plugs and wires, fan belts.
I changed my fuel pump regulator and my truck will not start, what do i need to check?
air in the fuel rail. look for what looks like a tire valve on the fuel rail.take the cap off depress the needle valve inside while someone cranks the truck,do this until gas starts to come out.truck should start.Did you change you fuel filter?Are you sure the regulator was the problem? Might have a bad fuel pump.
maybe fuel pump was the problem? check for fuel pressure and spark.
LUMINA 2006-Problem with fuel pump?
My car is Lumnia 2006 LS. It has a continuous sound from back side while engine working. My mechanic said this is due to the problem with fuel pump. There is no missing. Can it run without changing fuel pump? Is it costly to change the fuel pump?
LUMINA 2006-Problem with fuel pump?
If you mean a motor type sound it is only the fuel pump energizing. If you do not experience any performance problems then leave it alone. You did not give specific problem, such as stalling,hesitation or no acceleration.
LUMINA 2006-Problem with fuel pump?
If you mean a motor type sound it is only the fuel pump energizing. If you do not experience any performance problems then leave it alone. You did not give specific problem, such as stalling,hesitation or no acceleration.
Change fuel pump and filter for jeep wagoneer 1989 wanted to know where fuse is located,will not fire?
Chase down why you aren't getting ignition before you buy more parts.
If you mean a 89 4.0 small Wagoneer with fuel injection, not getting ignition to the engine can be a lot of old school stuff - bad cap, rotor, wires, coil, etc. The fuel injection does need to calculate the engine position and timing for the injection - the computer does it all - and it does the same for ignition from the same source - a %26quot;cam position%26quot; sensor in the distributor, and a Crankshaft Position Sensor on the bellhousing.
I would disconnect and clean the connection for the CPS first. It's located at the back of the manifold next to the firewall. If it cranks up and starts, plan on replacing it soon anyway. If not, it could be completely shot, and a voltmeter to check the ohms resistance will find if it's in spec.
On late models with FI, always science out the sensors with a voltmeter first, before throwing money at parts that don't fix it.
Change fuel pump and filter for jeep wagoneer 1989 wanted to know where fuse is located,will not fire?
fuse for what?
Change fuel pump and filter for jeep wagoneer 1989 wanted to know where fuse is located,will not fire?
Most likely under the hood or under the dash.
its in a black box under the hood near the battery .networking ink video tape
If you mean a 89 4.0 small Wagoneer with fuel injection, not getting ignition to the engine can be a lot of old school stuff - bad cap, rotor, wires, coil, etc. The fuel injection does need to calculate the engine position and timing for the injection - the computer does it all - and it does the same for ignition from the same source - a %26quot;cam position%26quot; sensor in the distributor, and a Crankshaft Position Sensor on the bellhousing.
I would disconnect and clean the connection for the CPS first. It's located at the back of the manifold next to the firewall. If it cranks up and starts, plan on replacing it soon anyway. If not, it could be completely shot, and a voltmeter to check the ohms resistance will find if it's in spec.
On late models with FI, always science out the sensors with a voltmeter first, before throwing money at parts that don't fix it.
Change fuel pump and filter for jeep wagoneer 1989 wanted to know where fuse is located,will not fire?
fuse for what?
Change fuel pump and filter for jeep wagoneer 1989 wanted to know where fuse is located,will not fire?
Most likely under the hood or under the dash.
its in a black box under the hood near the battery .
2000 chevy cavalier fuel pump AGAIN?
Thanks for the answers on my other question. Now...does anybody have any experience with changing a fuel pump on the 2000 chevy cavalier with 2.2L motor? I know it's it the fuel tank and I'll have to drop the tank to get to it. Other than that...can it be done in our garage or do I need to take it to a real mechanic? We have alot of experience with cars. I ALWAYS change my own oil which is a pain on this car...I've changed the A/C compressor and a few other things. Is the fuel pump something I can do or is it out of my league? Thanks
Derek
2000 chevy cavalier fuel pump AGAIN?
Where do you live? If you have alot of rust it can be a real PITA, but if its not too bad, then its labor intensive, but not actually that difficult. You disconnect all the lines and wiring from the tank, drop the tank. Rotate the ring lock counter clockwise (you may need a hammer and a brass punch) then carefully, pull the sending unit out of the tank. Its not straingt so do just pull straight out, take your time so you dont bend it. (if you do your gauge wil be off) Take the pump off the sending unit. Make sure to replace the sock.(the white fuel filter on the bottom of the sending unit. The install is the reverse. It is made 1000x easier if you drain the tank first, and replace the fuel filter thats inline as well. If its plugged it may have caused the failure in the first place.
2000 chevy cavalier fuel pump AGAIN?
Changing the fuel pump is not that hard at all. The hardest part of the job for me (when I had to do it) was siphoning out all of the gasoline because getting the hose down in to the tank was a bit difficult. I ended up removing the hose from the filler neck and siphoning it out that way. Once you get the tank down and remove the fuel send assembly, the pump itself is very simple. It is identical to the little pump used on the washer fluid.
It is pretty simple once you get the tank out. If you are mechanically inclined, you should not any trouble. It is pretty much self explanatory.
i work for general motors and we dont do many fuel pumps on cavaliers, pretty uncommon. if you're confident on dropping the tank on your own the actual fuel pump itself is not that difficult to change. the pump and sending unit are one assembly now so it's pretty simple. we charge 2.5 hours in our shop to do that job. (just to give you an idea) good luck.
ps: it's a stinky job. (and make sure to try to burn as much of the gas out of the tank as you can before you start the job) makes it easier not to have to drain the tank out before you drop it!!!
Derek
2000 chevy cavalier fuel pump AGAIN?
Where do you live? If you have alot of rust it can be a real PITA, but if its not too bad, then its labor intensive, but not actually that difficult. You disconnect all the lines and wiring from the tank, drop the tank. Rotate the ring lock counter clockwise (you may need a hammer and a brass punch) then carefully, pull the sending unit out of the tank. Its not straingt so do just pull straight out, take your time so you dont bend it. (if you do your gauge wil be off) Take the pump off the sending unit. Make sure to replace the sock.(the white fuel filter on the bottom of the sending unit. The install is the reverse. It is made 1000x easier if you drain the tank first, and replace the fuel filter thats inline as well. If its plugged it may have caused the failure in the first place.
2000 chevy cavalier fuel pump AGAIN?
Changing the fuel pump is not that hard at all. The hardest part of the job for me (when I had to do it) was siphoning out all of the gasoline because getting the hose down in to the tank was a bit difficult. I ended up removing the hose from the filler neck and siphoning it out that way. Once you get the tank down and remove the fuel send assembly, the pump itself is very simple. It is identical to the little pump used on the washer fluid.
It is pretty simple once you get the tank out. If you are mechanically inclined, you should not any trouble. It is pretty much self explanatory.
i work for general motors and we dont do many fuel pumps on cavaliers, pretty uncommon. if you're confident on dropping the tank on your own the actual fuel pump itself is not that difficult to change. the pump and sending unit are one assembly now so it's pretty simple. we charge 2.5 hours in our shop to do that job. (just to give you an idea) good luck.
ps: it's a stinky job. (and make sure to try to burn as much of the gas out of the tank as you can before you start the job) makes it easier not to have to drain the tank out before you drop it!!!
How do you change the fuel pump on a 2000 Chevy Blazer?
its located in the tank, unless they have a access plate in the rear interior you will have to drop the tank
How do you change the fuel pump on a 2000 Chevy Blazer?
your gona have to pull out your whole fuel tank and then where the hag line goes into your tank shoudl screw out and the pump is in your tank..so make sure you drain your tank it'll take a long time do switch it out
How do you change the fuel pump on a 2000 Chevy Blazer?
man ese u need some mexican friends, we know all dis **** n well do it for a 24 of coronas, find some mexican friends ese,
Now that you have heard from all the smart a** here it the info.
First remove the neg cable from the battery. Jack up truck and support with jack stands.
Now disconnect the fuel filler lines. Next support the tank with a floor jack. Remove the tank hangers and lower the tank. Now disconnect the fuel lines. Now lower the tank to the ground, and remove the tank from the truck.
Remove the filler and remove the pump. Reinstall in reverse order
Do what gold wing said but before you remove the pump, clean all the loose dirt away from the opening in the tank. When you remove the ring holding in the pump and sending unit you can get dirt in the tank which is bad. Good luck.
The fuel pump is located in the gas tank. You must remove the cover that protects the gast tank and then the tank itself. Make sure you disconnect the fuel lines going into the fuel pump when dropping the tank. There is little slack. Once tank is down, remove fuel pump and replace with new. The fuel pump is an entire housing unit about 1' tall and 5%26quot; in diameter. It also has the fuel gauge sensor on it, so if you have been having problems with your gas gauge, this will be fixed as well.
How do you change the fuel pump on a 2000 Chevy Blazer?
your gona have to pull out your whole fuel tank and then where the hag line goes into your tank shoudl screw out and the pump is in your tank..so make sure you drain your tank it'll take a long time do switch it out
How do you change the fuel pump on a 2000 Chevy Blazer?
man ese u need some mexican friends, we know all dis **** n well do it for a 24 of coronas, find some mexican friends ese,
Now that you have heard from all the smart a** here it the info.
First remove the neg cable from the battery. Jack up truck and support with jack stands.
Now disconnect the fuel filler lines. Next support the tank with a floor jack. Remove the tank hangers and lower the tank. Now disconnect the fuel lines. Now lower the tank to the ground, and remove the tank from the truck.
Remove the filler and remove the pump. Reinstall in reverse order
Do what gold wing said but before you remove the pump, clean all the loose dirt away from the opening in the tank. When you remove the ring holding in the pump and sending unit you can get dirt in the tank which is bad. Good luck.
The fuel pump is located in the gas tank. You must remove the cover that protects the gast tank and then the tank itself. Make sure you disconnect the fuel lines going into the fuel pump when dropping the tank. There is little slack. Once tank is down, remove fuel pump and replace with new. The fuel pump is an entire housing unit about 1' tall and 5%26quot; in diameter. It also has the fuel gauge sensor on it, so if you have been having problems with your gas gauge, this will be fixed as well.
Where is the "fuel pick up pump" loacated on a 2001 dodge pu with a cummins engine?
my pu wouldn't start right away a few times, i changed the fuel filter, the fuel pump is working. when i turn it over fuel comes out of the hose on the bottom of the filter housing, the drain switch is turned off.
Where is the %26quot;fuel pick up pump%26quot; loacated on a 2001 dodge pu with a cummins engine?
the %26quot;lift pump%26quot; is below the fuel filter houseing and a little torward the firewall on the side of the block here is a diagram its number 1
http://www.cumminsdatabase.com/read.php?鈥?/a>
Where is the %26quot;fuel pick up pump%26quot; loacated on a 2001 dodge pu with a cummins engine?
Also if you are having trouble with it, there is a change over kit that places the pump inside the fuel tank. The lift pump has shown to be very unreliable and can cause injector pump failure.
Where is the %26quot;fuel pick up pump%26quot; loacated on a 2001 dodge pu with a cummins engine?
the %26quot;lift pump%26quot; is below the fuel filter houseing and a little torward the firewall on the side of the block here is a diagram its number 1
http://www.cumminsdatabase.com/read.php?鈥?/a>
Where is the %26quot;fuel pick up pump%26quot; loacated on a 2001 dodge pu with a cummins engine?
Also if you are having trouble with it, there is a change over kit that places the pump inside the fuel tank. The lift pump has shown to be very unreliable and can cause injector pump failure.
I have a 99 cavalier and it wont stay running.. we changed fuel filter and o2 sensor and checked fuel pump?
the fuel pump is good and it isn'tt the oxygen sensor. i really need my car does anyone know anything.. please dont leave anything dumb i only need help not sarcasm.
I have a 99 cavalier and it wont stay running.. we changed fuel filter and o2 sensor and checked fuel pump?
Did you check your fuel pressure regulator? Fuel filter? Have a kinked line somewhere or other restriction? My gut feeling (which isn't always right, but often is) is that fuel is somehow restricted or choked out. I am assuming that you could keep the engine running if you kept your foot on the gas pedal.
Next thing is a vacuum leak... look at the line going to your PCV valve for starters, then inspect all of the vacuum lines going out of the intake manifold. Check any elbows (sharp bends) in the hoses for cracks. Make sure they are all firmly seated on whatever they are connected to. A leak in the line going to your PCV valve, for example, can cause your car to sputter and die out at an intersection. Make sure your PCV valve rattles when you take it out, or else it's not working.
Check your air intake to make sure it's not clogged. Your car needs air to breathe, a constant unrestricted supply of fuel, and spark to run.
While probably not the case, you might have a sticking IAC (idle air control) valve. Often, but not always, those can be cleaned if you can remove the valve part from the motor part. Getting cleaner down in the motor is a no-no.
Hope this helps!
Robert
I have a 99 cavalier and it wont stay running.. we changed fuel filter and o2 sensor and checked fuel pump?
clean IAC and check fuel pressure
these are the most usual causes for hard starting,/bad idling and/or dying
I have a 99 cavalier and it wont stay running.. we changed fuel filter and o2 sensor and checked fuel pump?
Did you check your fuel pressure regulator? Fuel filter? Have a kinked line somewhere or other restriction? My gut feeling (which isn't always right, but often is) is that fuel is somehow restricted or choked out. I am assuming that you could keep the engine running if you kept your foot on the gas pedal.
Next thing is a vacuum leak... look at the line going to your PCV valve for starters, then inspect all of the vacuum lines going out of the intake manifold. Check any elbows (sharp bends) in the hoses for cracks. Make sure they are all firmly seated on whatever they are connected to. A leak in the line going to your PCV valve, for example, can cause your car to sputter and die out at an intersection. Make sure your PCV valve rattles when you take it out, or else it's not working.
Check your air intake to make sure it's not clogged. Your car needs air to breathe, a constant unrestricted supply of fuel, and spark to run.
While probably not the case, you might have a sticking IAC (idle air control) valve. Often, but not always, those can be cleaned if you can remove the valve part from the motor part. Getting cleaner down in the motor is a no-no.
Hope this helps!
Robert
I have a 99 cavalier and it wont stay running.. we changed fuel filter and o2 sensor and checked fuel pump?
clean IAC and check fuel pressure
these are the most usual causes for hard starting,/bad idling and/or dying
1990 Oldsmobile Eighty Eight royale fuel pump. i need to change the fuel pump?
i have a 1990 Oldsmobile Eighty Eight royale and i need some websites or videos that would help me change it i hvae the new fuel pump already. i just need somthing that would help me locate some bolts and or anythong else i would need thanks
1990 Oldsmobile Eighty Eight royale fuel pump. i need to change the fuel pump?
Go to auto zone .com and follow the links to repair section. It may help. Or just buy a repair manual for your car.
good luck....
1990 Oldsmobile Eighty Eight royale fuel pump. i need to change the fuel pump?
Bob: I am sorry to say this: but if you need that much help to change a part:
which could potentially cause a fire/explosion or severe Chemical burns too your skin and
or eyes, I implore you not to attempt this repair alone!
You should not experiment with this type of repair without the help of a certified
Technician!java get over feelings
1990 Oldsmobile Eighty Eight royale fuel pump. i need to change the fuel pump?
Go to auto zone .com and follow the links to repair section. It may help. Or just buy a repair manual for your car.
good luck....
1990 Oldsmobile Eighty Eight royale fuel pump. i need to change the fuel pump?
Bob: I am sorry to say this: but if you need that much help to change a part:
which could potentially cause a fire/explosion or severe Chemical burns too your skin and
or eyes, I implore you not to attempt this repair alone!
You should not experiment with this type of repair without the help of a certified
Technician!
My dodge neon 96 blows the fuel pump fuse when i start ignition, i changed the fuel pump, and ignition switch?
still happens can anyone out here help? Thank you
My dodge neon 96 blows the fuel pump fuse when i start ignition, i changed the fuel pump, and ignition switch?
As suggest, start looking over the wiring harness for worn through spots.
I had this problem, my O2 sensor was grounding against my axle.
Also the wiring harness next to the valve cover closest to the driver's side is also prone to exposed wiring.
later
My dodge neon 96 blows the fuel pump fuse when i start ignition, i changed the fuel pump, and ignition switch?
Sounds to me the fuel pump is going to ground when power is connecting to it. Make sure you don't have a pinched power wire leading to the fuel pump. This may be the case and the fuse will blow to prevent a fire from happening!
My dodge neon 96 blows the fuel pump fuse when i start ignition, i changed the fuel pump, and ignition switch?
As suggest, start looking over the wiring harness for worn through spots.
I had this problem, my O2 sensor was grounding against my axle.
Also the wiring harness next to the valve cover closest to the driver's side is also prone to exposed wiring.
later
My dodge neon 96 blows the fuel pump fuse when i start ignition, i changed the fuel pump, and ignition switch?
Sounds to me the fuel pump is going to ground when power is connecting to it. Make sure you don't have a pinched power wire leading to the fuel pump. This may be the case and the fuse will blow to prevent a fire from happening!
How much is it on average to have a mechanic change a fuel pump?
99 dodge 2500 ram 360 V8
How much is it on average to have a mechanic change a fuel pump?
I would call all the shops in my town and get an estimate. Write them down on a paper. After you have finished, see which one best suits you. If you have, for example, two that charge the same price, then I would go with the one that I think will do the best job. Good luck.
How much is it on average to have a mechanic change a fuel pump?
like 800
anywhere from $300-$400. suggest buying part yourself first, so you only have to pay labor.
I depends on where you live.... here in NC it runs about $425.00 including the pump if they repalce the module.... about $350 if they are replacing th epump and screen
How much is it on average to have a mechanic change a fuel pump?
I would call all the shops in my town and get an estimate. Write them down on a paper. After you have finished, see which one best suits you. If you have, for example, two that charge the same price, then I would go with the one that I think will do the best job. Good luck.
How much is it on average to have a mechanic change a fuel pump?
like 800
anywhere from $300-$400. suggest buying part yourself first, so you only have to pay labor.
I depends on where you live.... here in NC it runs about $425.00 including the pump if they repalce the module.... about $350 if they are replacing th epump and screen
How do I change a fuel pump 2000 hyundai Accent?
oklatom gives very good directions but you can also go to autozone.com and look at the repair manual online for your specific car.
How do I change a fuel pump 2000 hyundai Accent?
Using a proper pump and container, empty the fuel tank of fuel. Now put it up on the lift, place your transmission jack under the tank, and remove the fuel lines using the proper tool, and the straps that hold the tank in place.
Lower it to where you can get a good hold on it, and set it on the ground. Clean around the place where the fuel pump is held in place so as not to get dirt in the tank, then turn it counter clockwise until the hold down comes off. Remove the pump.
Put the new pump in place, put the hold down ring in place and turn it until it seats. Set the tank back on the jack and slide it into place until you can put the straps back on the tank to secure it. Reconnect the fuel line and lower the vehicle. Slide the tank where you drained the fuel to the car, reverse the pump and refill the tank. Test drive, making sure of course that the fuel gage is working as it should.
How do I change a fuel pump 2000 hyundai Accent?
Go to the servicing station
If you have to ask on YA you should be taking it to a qualified mechanic.
How do I change a fuel pump 2000 hyundai Accent?
Using a proper pump and container, empty the fuel tank of fuel. Now put it up on the lift, place your transmission jack under the tank, and remove the fuel lines using the proper tool, and the straps that hold the tank in place.
Lower it to where you can get a good hold on it, and set it on the ground. Clean around the place where the fuel pump is held in place so as not to get dirt in the tank, then turn it counter clockwise until the hold down comes off. Remove the pump.
Put the new pump in place, put the hold down ring in place and turn it until it seats. Set the tank back on the jack and slide it into place until you can put the straps back on the tank to secure it. Reconnect the fuel line and lower the vehicle. Slide the tank where you drained the fuel to the car, reverse the pump and refill the tank. Test drive, making sure of course that the fuel gage is working as it should.
How do I change a fuel pump 2000 hyundai Accent?
Go to the servicing station
If you have to ask on YA you should be taking it to a qualified mechanic.
How can I test a fuel pump in a 97 Chevy Express Van?
I have a 97 Chevy Express that just stalled out on me. The engine cranks when I turn the key but sounds like it's not getting any fuel. I changed the fuel filter, I can hear the fuel pump relay %26quot;click%26quot; on when turn the ignition key. I'm guessing maybe the fuel pump is bad. Since it's in the gas tank, I'd like to be able to be sure of that before tackling that job. OR is there another possiility that could be preventing it from starting?
How can I test a fuel pump in a 97 Chevy Express Van?
The only way to know is to put a pressure guage on the fuel rail. You may get fuel by pressing the valve but you have no way of knowing if it has the correct pressure.
You did not say what engine you have, but the 5.7L needs 60 to 66 psi.
How can I test a fuel pump in a 97 Chevy Express Van?
turn the key to the %26quot;on%26quot; position without turning over, go back to the tank and listen for a whine sound, if you dont hear that sound the pump is dead. also on the engine there is a fuel rail, on the rail there is a schrader valve, looks like a bike tire valve. put on safety glasses and depress the needle in the valve and hold while the key is on, this should let you bleed down the pressure. turn off for a couple seconds, then turn on and recheck for pressure, if you have high pressure again, the pump is ok.celebrity hair myspace quizzes
How can I test a fuel pump in a 97 Chevy Express Van?
The only way to know is to put a pressure guage on the fuel rail. You may get fuel by pressing the valve but you have no way of knowing if it has the correct pressure.
You did not say what engine you have, but the 5.7L needs 60 to 66 psi.
How can I test a fuel pump in a 97 Chevy Express Van?
turn the key to the %26quot;on%26quot; position without turning over, go back to the tank and listen for a whine sound, if you dont hear that sound the pump is dead. also on the engine there is a fuel rail, on the rail there is a schrader valve, looks like a bike tire valve. put on safety glasses and depress the needle in the valve and hold while the key is on, this should let you bleed down the pressure. turn off for a couple seconds, then turn on and recheck for pressure, if you have high pressure again, the pump is ok.
Are 96-2004 Astro vans known for fuel pump and suspension problems? i have changed suspension parts 2 much!?
Also have changed fuel pump twice already at 123K...1997 Astro van
Are 96-2004 Astro vans known for fuel pump and suspension problems? i have changed suspension parts 2 much!?
GM did update the fuel pump for the 95-99 Astros and S-10s. The problem is if you don't replace the entire module, that is, pump, sending unit, and sock, you don't get the update. If you just replace the pump, the problems will continue. As for the front suspension, GM has had a problem with idler arms for as long as I can remember. It became such a problem with idler arms going bad that GM released a memo in 1998 that the idler arms can have as much as 3/4 inch of play, and should be tested with the vehicle on the ground. Shops were lifting the vehicles and grabbing the center link to show you how 'bad' the play is, and were being improperly tested. If the center link won't move with the weight of the vehicle on the suspension, the idler arms aren't bad. Your vehicle has 2 of them. Don't let a shop hang the vehicle in the air to show you how bad the idler arms are. As for ball joints and tie rod ends on that model, you should be good for at least 100k-110k.
Are 96-2004 Astro vans known for fuel pump and suspension problems? i have changed suspension parts 2 much!?
yes torsion bars drop yet its a doosy of one
gm had a problem with the fuel pumps they was using back in the late 90,s but they corrected that one,you may be getting bad pumps it has happened to me a few times,as for the suspension,probably just a bushing worn out or something,but have it checked really good,good luck with it.
As far as i know they have the same pumps as the blazers and S-10s and i have had 2 go out on my blazer but that is just me but anyway i wish you the best of luck.... J-rod
Are 96-2004 Astro vans known for fuel pump and suspension problems? i have changed suspension parts 2 much!?
GM did update the fuel pump for the 95-99 Astros and S-10s. The problem is if you don't replace the entire module, that is, pump, sending unit, and sock, you don't get the update. If you just replace the pump, the problems will continue. As for the front suspension, GM has had a problem with idler arms for as long as I can remember. It became such a problem with idler arms going bad that GM released a memo in 1998 that the idler arms can have as much as 3/4 inch of play, and should be tested with the vehicle on the ground. Shops were lifting the vehicles and grabbing the center link to show you how 'bad' the play is, and were being improperly tested. If the center link won't move with the weight of the vehicle on the suspension, the idler arms aren't bad. Your vehicle has 2 of them. Don't let a shop hang the vehicle in the air to show you how bad the idler arms are. As for ball joints and tie rod ends on that model, you should be good for at least 100k-110k.
Are 96-2004 Astro vans known for fuel pump and suspension problems? i have changed suspension parts 2 much!?
yes torsion bars drop yet its a doosy of one
gm had a problem with the fuel pumps they was using back in the late 90,s but they corrected that one,you may be getting bad pumps it has happened to me a few times,as for the suspension,probably just a bushing worn out or something,but have it checked really good,good luck with it.
As far as i know they have the same pumps as the blazers and S-10s and i have had 2 go out on my blazer but that is just me but anyway i wish you the best of luck.... J-rod
Fuel Pump and parts and modification for 1995 F150?
I have a 1995 F150 XLT 302cc (5L). It's acting like it's about time to change fuel pump. Occasionally sputters, stalls or dies going down the road, and is occasionally hard to start. Which pump(s), filters etc does it need? Also I heard of a modification to prevent Radio Interference from the fuel pump (I am a ham radio operator). Do you know where I can find out about that, or is it a special part I should order?
Fuel Pump and parts and modification for 1995 F150?
i have had fuel pump problems before and none of them gave any evidence of failure other than loud operating noise. they just die. the problems you listed you may want to do a little more troubleshooting before you just go and replace the fuel pump. check your filter, and check the voltage going to the fuel pump and check for fuel flow from the pump, if all this checks good then something else, if fuel pump does sputter fuel and no continious flow then yes change the pump.
Fuel Pump and parts and modification for 1995 F150?
you can try www.f150online.com
just because it's acting like a fuel problem, don't neglect the electrical side of the story!!!! i.e plugs wires distributor etc.
Fuel Pump and parts and modification for 1995 F150?
i have had fuel pump problems before and none of them gave any evidence of failure other than loud operating noise. they just die. the problems you listed you may want to do a little more troubleshooting before you just go and replace the fuel pump. check your filter, and check the voltage going to the fuel pump and check for fuel flow from the pump, if all this checks good then something else, if fuel pump does sputter fuel and no continious flow then yes change the pump.
Fuel Pump and parts and modification for 1995 F150?
you can try www.f150online.com
just because it's acting like a fuel problem, don't neglect the electrical side of the story!!!! i.e plugs wires distributor etc.
Subscribe to:
Posts
(Atom)